Difference between revisions of "3D Printed Parts"

From Jubilee
Jump to navigation Jump to search
(9 intermediate revisions by 2 users not shown)
Line 9: Line 9:
 
* outer perimeter layer first
 
* outer perimeter layer first
 
* 2-3mm brim recommended, but not required
 
* 2-3mm brim recommended, but not required
 +
* ''uncheck'' "Detect Thin Walls" if your Slicer has this settings.
 +
** Otherwise, small gaps will not be filled.
  
 
However, exceptions do exist! Please check the breakdown below for exceptions.
 
However, exceptions do exist! Please check the breakdown below for exceptions.
Line 19: Line 21:
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|-
 
|-
−
! Quantity !! Part !! Note
+
! Quantity !! Part Source !! Note
 
|-
 
|-
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/psu_socket_holder.STL PSU Socket Holder] ||  
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/psu_socket_holder.STL PSU Socket Holder] ||  
Line 44: Line 46:
 
|-
 
|-
 
| 2 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/belt_clasp.STL belt_clasp.STL] ||  
 
| 2 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/belt_clasp.STL belt_clasp.STL] ||  
−
|-
 
−
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_left_leadscrew_retainer.STL front_left_leadscrew_retainer.STL] ||
 
−
|-
 
−
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_right_leadscrew_retainer.STL front_right_leadscrew_retainer.STL] ||
 
−
|-
 
−
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_leadscrew_retainer.STL back_leadscrew_retainer.STL] ||
 
 
|-
 
|-
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_right_foot.STL back_right_foot.STL] || 2 perimeter layers is sufficient
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_right_foot.STL back_right_foot.STL] || 2 perimeter layers is sufficient
Line 79: Line 75:
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|-
 
|-
−
! Quantity !! Part !! Note
+
! Quantity !! Part Source !! Note
 
|-
 
|-
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/toolchanger/toolchange_carriage/spring_guide_capture.STL spring_guide_capture.stl] ||
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/toolchanger/toolchange_carriage/spring_guide_capture.STL spring_guide_capture.stl] ||
Line 110: Line 106:
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|-
 
|-
−
! Quantity !! Part !! Note
+
! Quantity !! Part Source !! Note
 
|-
 
|-
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/jubilee_tools/tools/extruders/direct_drive_bondtech_groovemount_extruder/fabrication_exports/ooze_wiper.STL ooze_wiper.STL] || ''per tool''
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/jubilee_tools/tools/extruders/direct_drive_bondtech_groovemount_extruder/fabrication_exports/ooze_wiper.STL ooze_wiper.STL] || ''per tool''
Line 129: Line 125:
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/coupling_plate_pin_insertion_fixture.STL coupling_plate_pin_insertion_fixture.STL] ||
 
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/coupling_plate_pin_insertion_fixture.STL coupling_plate_pin_insertion_fixture.STL] ||
 
|-
 
|-
−
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/z_lift_pin_insertion_fixture.STL z_lift_pin_insertion_fixture.STL] ||
+
| 1 || [https://github.com/machineagency/jubilee/blob/dev/jubilee_2.2.0/tools/assembly_fixtures/z_lift_pin_insertion_fixture.STL z_lift_pin_insertion_fixture.STL] ||
−
|-
 
−
| 8 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/outer_frame_squaring_plate.STL outer_frame_squaring_plate.STL] ||
 
 
|}
 
|}
  
 
== Deprecated Parts ==
 
== Deprecated Parts ==
 
These parts are no longer necessary in the latest version. They are:
 
These parts are no longer necessary in the latest version. They are:
−
* 1x [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/left_motor_plate.STL left_motor_plate.STL]
+
 
−
** print from PETG
+
{| class="wikitable sortable"
−
** Note: an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available.
+
|-
−
* 1x [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/right_motor_plate.STL right_motor_plate.STL]
+
! Quantity !! Part Source !! Note
−
** print from PETG
+
|-
−
** Note: an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available.
+
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_left_leadscrew_retainer.STL front_left_leadscrew_retainer.STL] ||
 +
|-
 +
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_right_leadscrew_retainer.STL front_right_leadscrew_retainer.STL] ||
 +
|-
 +
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_leadscrew_retainer.STL back_leadscrew_retainer.STL] ||
 +
|-
 +
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/left_motor_plate.STL left_motor_plate.STL] ||  print from PETG
 +
'''Note''': an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available.
 +
|-
 +
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/right_motor_plate.STL right_motor_plate.STL] ||  print from PETG
 +
'''Note''': an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available.
 +
|-
 +
| 8 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/outer_frame_squaring_plate.STL outer_frame_squaring_plate.STL] ||
 +
|}

Revision as of 23:34, 11 December 2020

Default Print Settings

Print all parts with the following print settings:

  • PLA
  • 0.4mm nozzle
  • No supports
  • 0.2mm layer height
  • 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
  • 20% infill * printable in the provided orientations
  • outer perimeter layer first
  • 2-3mm brim recommended, but not required
  • uncheck "Detect Thin Walls" if your Slicer has this settings.
    • Otherwise, small gaps will not be filled.

However, exceptions do exist! Please check the breakdown below for exceptions.

Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.

Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.

Frame Printed Parts and Quantities

Quantity Part Source Note
1 PSU Socket Holder
1 Left Crossbar Pulley Reinforcement Plate
1 Right Crossbar Pulley Reinforcement Plate
1 Left Corner Pulley Reinforcement Plate
1 Right Corner Pulley Reinforcement Plate
2 Motor Reinforcement Plate
1 x_limit_trigger.STL
3 z_thrust_bearing_spacer.STL
1 back_z_motor_plate.STL
1 front_left_z_motor_plate.STL
1 front_right_z_motor_plate.STL
2 belt_clasp.STL
1 back_right_foot.STL 2 perimeter layers is sufficient
1 back_left_foot.STL 2 perimeter layers is sufficient
1 front_right_foot.STL 2 perimeter layers is sufficient
1 front_left_foot.STL 2 perimeter layers is sufficient
1 front_left_bed_coupling_lift.STL
1 front_right_bed_coupling_lift.STL
1 back_bed_coupling_lift.STL
1 left_motor_corner_plate_spacer.STL
1 right_motor_corner_plate_spacer.STL
1 left_double_pulley_corner_bracket.STL print with support material
1 right_double_pulley_corner_bracket.STL print with support material
4 printed_pulley_spacer.STL

Toolchanger Parts and Quantities

Quantity Part Source Note
1 spring_guide_capture.stl
1 twist_lock_spacer.STL
1 carriage_back_plate.STL
1 carriage_center_plate.STL
1 carriage_coupler_plate.STL
1 carriage_pulley.STL
1 fixed_half_pulley.STL
1 knob.STL
1 floating_half_pulley.STL print with support material
1 lock_actuator_base_plate.STL or stepperonline_lock_actuator_base_plate.STL
1 lock_actuator_motor_clip.STL or stepperonline_lock_actuator_motor_clip.STL
1 spring_guide_anchor_block.STL OPTIONAL

Extruder-Specific Frame Parts

Quantity Part Source Note
1 ooze_wiper.STL per tool
1 tool_cable_management_bracket.STL per tool
1 parking_post_base_47mm.STL per tool
1 tool_holder_47mm.STL per tool

Assembly Fixtures Parts and Quantities

Quantity Part Source Note
1 coupling_plate_pin_insertion_fixture.STL
1 z_lift_pin_insertion_fixture.STL

Deprecated Parts

These parts are no longer necessary in the latest version. They are:

Quantity Part Source Note
1 front_left_leadscrew_retainer.STL
1 front_right_leadscrew_retainer.STL
1 back_leadscrew_retainer.STL
1 left_motor_plate.STL print from PETG

Note: an aluminum version of this part is now available.

1 right_motor_plate.STL print from PETG

Note: an aluminum version of this part is now available.

8 outer_frame_squaring_plate.STL
Retrieved from "https://jubilee3d.com/index.php?title=3D_Printed_Parts&oldid=3225"