Difference between revisions of "3D Printed Parts"
Jump to navigation
Jump to search
Smoonerlater (talk | contribs) |
Poofjunior (talk | contribs) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 9: | Line 9: | ||
* outer perimeter layer first | * outer perimeter layer first | ||
* 2-3mm brim recommended, but not required | * 2-3mm brim recommended, but not required | ||
| + | * ''uncheck'' "Detect Thin Walls" if your Slicer has this settings. | ||
| + | ** Otherwise, small gaps will not be filled. | ||
However, exceptions do exist! Please check the breakdown below for exceptions. | However, exceptions do exist! Please check the breakdown below for exceptions. | ||
| Line 44: | Line 46: | ||
|- | |- | ||
| 2 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/belt_clasp.STL belt_clasp.STL] || | | 2 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/belt_clasp.STL belt_clasp.STL] || | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|- | |- | ||
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_right_foot.STL back_right_foot.STL] || 2 perimeter layers is sufficient | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_right_foot.STL back_right_foot.STL] || 2 perimeter layers is sufficient | ||
| Line 129: | Line 125: | ||
| 1 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/coupling_plate_pin_insertion_fixture.STL coupling_plate_pin_insertion_fixture.STL] || | | 1 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/coupling_plate_pin_insertion_fixture.STL coupling_plate_pin_insertion_fixture.STL] || | ||
|- | |- | ||
| − | | 1 || [https://github.com/machineagency/jubilee/blob/ | + | | 1 || [https://github.com/machineagency/jubilee/blob/dev/jubilee_2.2.0/tools/assembly_fixtures/z_lift_pin_insertion_fixture.STL z_lift_pin_insertion_fixture.STL] || |
| − | |||
| − | |||
|} | |} | ||
| Line 140: | Line 134: | ||
|- | |- | ||
! Quantity !! Part Source !! Note | ! Quantity !! Part Source !! Note | ||
| + | |- | ||
| + | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_left_leadscrew_retainer.STL front_left_leadscrew_retainer.STL] || | ||
| + | |- | ||
| + | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/front_right_leadscrew_retainer.STL front_right_leadscrew_retainer.STL] || | ||
| + | |- | ||
| + | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/back_leadscrew_retainer.STL back_leadscrew_retainer.STL] || | ||
|- | |- | ||
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/left_motor_plate.STL left_motor_plate.STL] || print from PETG | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/left_motor_plate.STL left_motor_plate.STL] || print from PETG | ||
| Line 146: | Line 146: | ||
| 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/right_motor_plate.STL right_motor_plate.STL] || print from PETG | | 1 || [https://github.com/machineagency/jubilee/blob/master/frame/fabrication_exports/3d_printed_parts/frame/right_motor_plate.STL right_motor_plate.STL] || print from PETG | ||
'''Note''': an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available. | '''Note''': an [https://www.mandalaroseworks.com/jubilee/stepperMounts aluminum version] of this part is now available. | ||
| + | |- | ||
| + | | 8 || [https://github.com/machineagency/jubilee/blob/master/tools/assembly_fixtures/outer_frame_squaring_plate.STL outer_frame_squaring_plate.STL] || | ||
|} | |} | ||
Revision as of 23:34, 11 December 2020
Default Print Settings
Print all parts with the following print settings:
- PLA
- 0.4mm nozzle
- No supports
- 0.2mm layer height
- 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
- 20% infill * printable in the provided orientations
- outer perimeter layer first
- 2-3mm brim recommended, but not required
- uncheck "Detect Thin Walls" if your Slicer has this settings.
- Otherwise, small gaps will not be filled.
However, exceptions do exist! Please check the breakdown below for exceptions.
Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.
Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.
Frame Printed Parts and Quantities
| Quantity | Part Source | Note |
|---|---|---|
| 1 | PSU Socket Holder | |
| 1 | Left Crossbar Pulley Reinforcement Plate | |
| 1 | Right Crossbar Pulley Reinforcement Plate | |
| 1 | Left Corner Pulley Reinforcement Plate | |
| 1 | Right Corner Pulley Reinforcement Plate | |
| 2 | Motor Reinforcement Plate | |
| 1 | x_limit_trigger.STL | |
| 3 | z_thrust_bearing_spacer.STL | |
| 1 | back_z_motor_plate.STL | |
| 1 | front_left_z_motor_plate.STL | |
| 1 | front_right_z_motor_plate.STL | |
| 2 | belt_clasp.STL | |
| 1 | back_right_foot.STL | 2 perimeter layers is sufficient |
| 1 | back_left_foot.STL | 2 perimeter layers is sufficient |
| 1 | front_right_foot.STL | 2 perimeter layers is sufficient |
| 1 | front_left_foot.STL | 2 perimeter layers is sufficient |
| 1 | front_left_bed_coupling_lift.STL | |
| 1 | front_right_bed_coupling_lift.STL | |
| 1 | back_bed_coupling_lift.STL | |
| 1 | left_motor_corner_plate_spacer.STL | |
| 1 | right_motor_corner_plate_spacer.STL | |
| 1 | left_double_pulley_corner_bracket.STL | print with support material |
| 1 | right_double_pulley_corner_bracket.STL | print with support material |
| 4 | printed_pulley_spacer.STL |
Toolchanger Parts and Quantities
| Quantity | Part Source | Note |
|---|---|---|
| 1 | spring_guide_capture.stl | |
| 1 | twist_lock_spacer.STL | |
| 1 | carriage_back_plate.STL | |
| 1 | carriage_center_plate.STL | |
| 1 | carriage_coupler_plate.STL | |
| 1 | carriage_pulley.STL | |
| 1 | fixed_half_pulley.STL | |
| 1 | knob.STL | |
| 1 | floating_half_pulley.STL | print with support material |
| 1 | lock_actuator_base_plate.STL or stepperonline_lock_actuator_base_plate.STL | |
| 1 | lock_actuator_motor_clip.STL or stepperonline_lock_actuator_motor_clip.STL | |
| 1 | spring_guide_anchor_block.STL | OPTIONAL |
Extruder-Specific Frame Parts
| Quantity | Part Source | Note |
|---|---|---|
| 1 | ooze_wiper.STL | per tool |
| 1 | tool_cable_management_bracket.STL | per tool |
| 1 | parking_post_base_47mm.STL | per tool |
| 1 | tool_holder_47mm.STL | per tool |
Assembly Fixtures Parts and Quantities
| Quantity | Part Source | Note |
|---|---|---|
| 1 | coupling_plate_pin_insertion_fixture.STL | |
| 1 | z_lift_pin_insertion_fixture.STL |
Deprecated Parts
These parts are no longer necessary in the latest version. They are:
| Quantity | Part Source | Note |
|---|---|---|
| 1 | front_left_leadscrew_retainer.STL | |
| 1 | front_right_leadscrew_retainer.STL | |
| 1 | back_leadscrew_retainer.STL | |
| 1 | left_motor_plate.STL | print from PETG
Note: an aluminum version of this part is now available. |
| 1 | right_motor_plate.STL | print from PETG
Note: an aluminum version of this part is now available. |
| 8 | outer_frame_squaring_plate.STL |