3D Printed Parts

From Jubilee
Revision as of 10:39, 17 February 2021 by Poofjunior (talk | contribs) (→‎Toolchanger Parts and Quantities)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Default Print Settings

Print all parts with the following print settings:

  • PLA
  • 0.4mm nozzle
  • No supports
  • 0.2mm layer height
  • 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
  • 20% infill * printable in the provided orientations
  • outer perimeter layer first
  • 2-3mm brim recommended, but not required
  • uncheck "Detect Thin Walls" if your Slicer has this settings.
    • Otherwise, small gaps will not be filled.

However, exceptions do exist! Please check the breakdown below for exceptions.

Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.

Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.

Frame Printed Parts and Quantities

Quantity Part Source Note
1 PSU Socket Holder
1 Left Crossbar Pulley Reinforcement Plate
1 Right Crossbar Pulley Reinforcement Plate
1 Left Corner Pulley Reinforcement Plate
1 Right Corner Pulley Reinforcement Plate
2 Motor Reinforcement Plate
1 x_limit_trigger.STL
3 z_thrust_bearing_spacer.STL
1 back_z_motor_plate.STL
1 front_left_z_motor_plate.STL
1 front_right_z_motor_plate.STL
2 belt_clasp.STL
1 back_right_foot.STL 2 perimeter layers is sufficient
1 back_left_foot.STL 2 perimeter layers is sufficient
1 front_right_foot.STL 2 perimeter layers is sufficient
1 front_left_foot.STL 2 perimeter layers is sufficient
1 front_left_bed_coupling_lift.STL
1 front_right_bed_coupling_lift.STL
1 back_bed_coupling_lift.STL
1 left_motor_corner_plate_spacer.STL
1 right_motor_corner_plate_spacer.STL
1 left_double_pulley_corner_bracket.STL print with support material
1 right_double_pulley_corner_bracket.STL print with support material
4 printed_pulley_spacer.STL

Toolchanger Parts and Quantities

Quantity Part Source Note
1 spring_guide_capture.stl
1 twist_lock_spacer.STL
1 carriage_back_plate.STL
1 carriage_center_plate.STL
1 carriage_coupler_plate.STL
1 carriage_pulley.STL
1 fixed_half_pulley.STL
1 knob.STL
1 floating_half_pulley.STL print with support material.

Do not print from a matte or composite material, which adds friction to the spring's sliding surface.

1 lock_actuator_base_plate.STL or stepperonline_lock_actuator_base_plate.STL
1 lock_actuator_motor_clip.STL or stepperonline_lock_actuator_motor_clip.STL
1 spring_guide_anchor_block.STL OPTIONAL

Extruder-Specific Frame Parts

Quantity Part Source Note
1 ooze_wiper.STL per tool
1 tool_cable_management_bracket.STL per tool
1 parking_post_base_47mm.STL per tool
1 tool_holder_47mm.STL per tool

Assembly Fixtures Parts and Quantities

Quantity Part Source Note
1 coupling_plate_pin_insertion_fixture.STL
1 z_lift_pin_insertion_fixture.STL

Deprecated Parts

These parts are no longer necessary in the latest version. They are:

Quantity Part Source Note
1 front_left_leadscrew_retainer.STL
1 front_right_leadscrew_retainer.STL
1 back_leadscrew_retainer.STL
1 left_motor_plate.STL print from PETG

Note: an aluminum version of this part is now available.

1 right_motor_plate.STL print from PETG

Note: an aluminum version of this part is now available.

8 outer_frame_squaring_plate.STL