Difference between revisions of "Purchased Parts"
Poofjunior (talk | contribs) |
Poofjunior (talk | contribs) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 17: | Line 17: | ||
Some small-scale manufacturers and part vendors are either reselling Jubilee’s hard-to-make parts, consolidating parts into kits, or selling modified parts from the stock model. These vendors are: | Some small-scale manufacturers and part vendors are either reselling Jubilee’s hard-to-make parts, consolidating parts into kits, or selling modified parts from the stock model. These vendors are: | ||
* [https://713maker.com/jubilee 713Maker] | * [https://713maker.com/jubilee 713Maker] | ||
| − | ** [https:// | + | ** [https://713maker.com/jubilee/jubilee-magnetic-heated-bed Magnetic bed plates] |
** [https://713maker.com/jubilee/jubilee-heated-bed Non-magnetic bed plates] | ** [https://713maker.com/jubilee/jubilee-heated-bed Non-magnetic bed plates] | ||
* [https://www.mandalaroseworks.com/shop/jubilee Mandala Rose Works] | * [https://www.mandalaroseworks.com/shop/jubilee Mandala Rose Works] | ||
| + | ** [https://www.mandalaroseworks.com/shop/mrw-products/jubilee-magbed Magnetic bed plates] | ||
** [https://www.mandalaroseworks.com/shop/mrw-products/jubilee-crossbar Jubilee crossbar] | ** [https://www.mandalaroseworks.com/shop/mrw-products/jubilee-crossbar Jubilee crossbar] | ||
| − | ** [https://www.mandalaroseworks.com/shop/mrw-products/ | + | ** [https://www.mandalaroseworks.com/shop/mrw-products/jubilee-aluminum-stepper-mounts Aluminum stepper mounts] |
| − | ** [https://www.mandalaroseworks.com/shop/mrw-products/ | + | ** [https://www.mandalaroseworks.com/shop/mrw-products/jubilee-front-corner-brackets Aluminum corner brackets] |
* [https://www.seemecnc.com/collections/jubilee/ SeeMeCNC] | * [https://www.seemecnc.com/collections/jubilee/ SeeMeCNC] | ||
** [https://www.seemecnc.com/products/jubilee-back-side-panel?_pos=2&_sid=51372dc9d&_ss=r V1 back panel] | ** [https://www.seemecnc.com/products/jubilee-back-side-panel?_pos=2&_sid=51372dc9d&_ss=r V1 back panel] | ||
Revision as of 19:19, 22 February 2021
Purchased parts for Jubilee are broken down into multiple shopping lists
- (Current) Jubilee V2.1.2
- V2 Frame Shopping List (~$1350)
- V2 2x Direct Drive Extruder Shopping List (~$200 per tool)
- (Community Contributed) Jubilee V2.0.2 UK/EU BOM by HaythamB
- V2.0.2 Frame Shopping List last updated Apr 12, 2020
- (Deprecated) Jubilee V1
- V1 Frame Shopping List (~$1550)
- V1 2x Direct-Drive Extruder Shopping List (~$200 per tool)
Warnings About Cutting Your Own Extrusions
The shopping list specifies that the 2020 extrusions be cut-to-length by the vendor Misumi. This choice is intentional because Misumi can cut parts better (typically within +/- 0.1mm) than most Jubilee builders can without specialized tools. Later sections of the instructions also assume that extrusions of the same length are actually the same length; otherwise the squaring techniques in the instructions will not work. Long-story short: don’t cut the extrusions yourself unless you have a highly repeatable cutting setup.
Jubilee Component Vendors
Some small-scale manufacturers and part vendors are either reselling Jubilee’s hard-to-make parts, consolidating parts into kits, or selling modified parts from the stock model. These vendors are:
- 713Maker
- Mandala Rose Works
- SeeMeCNC
- Double Jump Electric (Joshua Vasquez)
- Filastruder
- Twist Locks
- T8x2 and T8x4 Leadscrews, 375mm long
- Tool Wedge Plates
- M3 and M4 Heat Set Inserts
- REL Extension Spring
- REL Hub
- Spring Guide
- Thrust Bearings
- Jubilee LDO Motor Kit
- Gates Pulley/Idler/Belt Motion Set
- Tool Balls
- Plum Couplers
- Shoulder Screws
- Jubilee Back Panel
- Coming Soon: Jubilee Fastener Kit
- Luke’s Laboratory
- High Temp 3D
- Powge
- Printed Solid
Alternates
Depending on region-specific constraints some parts may be harder to purchase. We welcome suggestions and will list them here.