Difference between revisions of "Specifying Your Build Options"
Jump to navigation
Jump to search
Poofjunior (talk | contribs) |
Poofjunior (talk | contribs) |
||
| Line 18: | Line 18: | ||
=== 305x305mm Magnetic Build Plate Options === | === 305x305mm Magnetic Build Plate Options === | ||
| − | * '''Budget''' | + | * '''Budget:''' [https://www.seemecnc.com/products/fablam-flex-spring-steel-bed-plate-for-jubilee?_pos=11&_sid=e2a6a3d11&_ss=r Fablam Flexplate] by SeeMeCNC |
** Save $30US. These may become the default in a future revision. | ** Save $30US. These may become the default in a future revision. | ||
| − | * '''Default''' | + | * '''Default:''' [https://www.buildtak.com/product/flexplate-surface/ BuildTak Flexplate] |
=== Crossbar Options === | === Crossbar Options === | ||
Revision as of 00:29, 11 May 2020
The V2 Shopping List assumes configuring Jubilee for 3D printing with two tool heads, but some alternate parts might be better for different use cases. All options are listed below, and options labeled as default are present in this shopping list.
Frame Configuration
Electronics Options
- Default: Duet2 + Duex5
- Duet3 + Raspberry Pi + 2 Duet Expander Boards
- this is not yet officially supported with a config file, but the back panel has a hole pattern to accomodate these boards.
Bed Options
- Budget: Plain MIC6 Aluminum Plate + 305x305 High Temperature Magnetic Sheet
- Save ~$50US. The heated bed will take an extra minute or two to heat up. You will also need to apply the sticky magnetic sheet as an extra step.
- Default: MIC6 Aluminum Plate with embedded magnets
- This bed plate should be fine operating at temperatures no more than 150C. Check your vendor for this limit.
- MIC6 Aluminum Plate BYOM (Bring your own magnets) Style
- This plate has pockets for magnets, but you will need to supply your own magnets
305x305mm Magnetic Build Plate Options
- Budget: Fablam Flexplate by SeeMeCNC
- Save $30US. These may become the default in a future revision.
- Default: BuildTak Flexplate
Crossbar Options
- Default: Aluminum Crossbar
- a pocketed aluminum crossbar, enabling the machine to carry heavier tools and operate at higher temperatures without warping. It is also substantially easier to assemble than the carbon fiber crossbar.
- ~160 grams
- Top Speed: 15000 - 20000 mm/min.
- US Vendor: Mandala Rose Works
- EU Stockist: hightemp3d
- Deprecated: 6mm Carbon Fiber Crossbar
- Light and stiff. This option was part of the original design, made by requesting a custom DXF from CNCMadness and installing four press-fit composite inserts. Assembly Instructions remain on the wiki.
- ~140 grams + 20 grams with inserts
- Top Speed: 15000 - 20000 mm/min.
XY Motor Options
- Default: Stepper Online Motors
- Part Number: 17HM19-2004S1 Spec Sheet
- Upgrade: LDO 0.9 Nema 17 MAX Power Motors sold by Filastruder
- Part Number: LDO-42STH60-2004MAC(RC) Spec Sheet
Tools
Extruder Options
- The Default Extruder can accommodate an E3D V6 (default) or Volcano nozzle without adjusting the heights of other components.
Upgrades
- Metal Corner Plates - Made by Mandala Rose Works (also sold by hightemp3d in the EU)
- Metal Stepper Plates - Made by Mandala Rose Works (also sold by hightemp3d in the EU)
- These stepper plates are stiffer and have the added benefit of acting like heatsinks for the XY motors.
Planned Upgrades
- [Hemera Extruder Tool]
- [9mm Belt Upgrade]
- [E3D Tool Plate Style Bondtech Extruder] comparable to the default extruder