Difference between revisions of "Bondtech Direct Drive Extruder"

Revision as of 11:53, 7 August 2020

This is the default extruder. It’s compatible with both an E3D V6 and an E3D Volcano hotend. This extruder will work with the fabrications specs below with nozzle temps up to 250C and a bed plate temperature up to 80C.

Note: motor heatsinks are not optional! If you operate the motors without heatsinks, the tool plates will warp from the heat. Exposure to radiated heat from the nozzle and the bed is fine up to 80C

Parts to Buy

For a set of two extruders, all parts to buy are called out in this spreadsheet tab.

Assembly Tools

1x PTFE Tube Cutter
1x E3D Nozzle Spanner Wrench

3D Printed Parts and Settings

Common Settings

PLA
0.4mm nozzle
No supports
0.2mm layer height
6 perimters
20% infill (any pattern)

Parts and Special Settings

Blower Fan Shroud
- Print with support material
Tool Plate
- 100% infill (yeup, solid)
Extruder Holder
Groovemount Clip
Left Parking Wing
Right Parking Wing
Wedge Plate
- 0.1mm layer height. This is critical
Ooze Wiper
Tool Cable Management Bracket
Parking Post Base 55mm
Tool Holder 55mm

Assembly Instructions

Wiring

There are many ways to wire Jubilee tools, so feel free to take the option below as a suggestion.

Default Wiring Diagram Option

Note that these wires are rather long because they must loop over the frame in an arch fashion and then return under the frame to the back of the machine where they are plugged into the control boards.

The image on the right shows how to wire tool1 (Extruder 0, E0) to the Duet.

Software Configuration

Duet 2 or 3

Note that the items shown in < > signs are placeholders and should be replaced with the values you actually have. (Remove the < > signs too!)

The Duet ecosystem assumes that tools are connected to single motor drive. Motor drives are numbered starting from 0. Define a motor drive with:

M569 P<motor_drive_index> S0

(S1 inverts the direction of the motor drive.)

Tools are numbered starting from 0. Define the tool index, tool name, and connect the motor drive that will control it with:

M563 P<tool_index> S"My Chocolate Extruder" D<motor_drive_index> H1 F0

Define the tool offset from the ZProbe trigger location. These can be set to all zero for now and set later.

G10 P<tool_index> X-4.5 Y44.02 Z-2.25

Optional: define the default operating and standby temperatures. These can be omitted since most 3D Printer Slicer programs will set these at the start of the print.

G10 P0 S<extruding_temperature> R<standby_temperature>

Optional: define this extruder's pressure advance value. This can be omitted (implying a value of 0), but a value of 0.1 seems to be a good starting point for this particular extruder.

M572 D<motor_drive_index> S0.1

The Duet ecosystem assumes that each extruder has a single temperature sensor. Define this extruder's temperature sensor index.

TODO

The Duet ecosystem assumes that each extruder has a single heater cartridge. Define this extruder's temperature sensor index.

TODO

Put all these lines of code in your config file.

Klipper

Not yet implemented

@@ Line 45: / Line 45: @@
 * [https://docs.google.com/viewer?url=https://github.com/machineagency/jubilee/raw/master/tools/jubilee_tools/tools/extruders/direct_drive_bondtech_groovemount_extruder/assembly_instructions/bondtech_groovemount_extruder_assembly_instructions.pdf Tool Assembly Instructions]
 * [https://docs.google.com/viewer?url=https://github.com/machineagency/jubilee/raw/master/tools/jubilee_tools/tool_posts/configurable_tool_post/assembly_instructions/parking_post_assembly_instructions.pdf Parking Post Assembly Instructions]
-* [https://docs.google.com/viewer?url=https://github.com/machineagency/jubilee/blob/master/tools/jubilee_tools/tools/extruders/ooze_wipers/documentation/ooze_wiper_assembly.pdf Ooze Wiper Assembly Instructions]
+* [https://docs.google.com/viewer?url=https://github.com/machineagency/jubilee/raw/master/tools/jubilee_tools/tools/extruders/ooze_wipers/documentation/ooze_wiper_assembly.pdf Ooze Wiper Assembly Instructions]
 == Wiring ==