Difference between revisions of "Purchased Parts"
Poofjunior (talk | contribs) |
Poofjunior (talk | contribs) |
||
| Line 46: | Line 46: | ||
** [https://www.filastruder.com/collections/jubilee/products/wire-cable-and-spring-guide-set-for-jubilee Spring Guide] | ** [https://www.filastruder.com/collections/jubilee/products/wire-cable-and-spring-guide-set-for-jubilee Spring Guide] | ||
** [https://www.filastruder.com/collections/jubilee/products/thrust-bearing-for-jubilee-z-motors Thrust Bearings] | ** [https://www.filastruder.com/collections/jubilee/products/thrust-bearing-for-jubilee-z-motors Thrust Bearings] | ||
| − | ** [https://www.filastruder.com/collections/jubilee/products/ldo-stepper-motor-set-for-jubilee Jubilee Motor Kit] | + | ** [https://www.filastruder.com/collections/jubilee/products/ldo-stepper-motor-set-for-jubilee Jubilee LDO Motor Kit] |
** [https://www.filastruder.com/collections/jubilee/products/gates-motion-set-for-jubilee-printers Gates Pulley/Idler/Belt Motion Set] | ** [https://www.filastruder.com/collections/jubilee/products/gates-motion-set-for-jubilee-printers Gates Pulley/Idler/Belt Motion Set] | ||
** [https://www.filastruder.com/collections/jubilee/products/tool-balls-for-jubilee-3-pack Tool Balls] | ** [https://www.filastruder.com/collections/jubilee/products/tool-balls-for-jubilee-3-pack Tool Balls] | ||
| Line 68: | Line 68: | ||
** [https://hightemp3d.com/products/aluminum-hub-6-jubilee-toolchanger-3d-printer Aluminum Hub, 6 mm ID] | ** [https://hightemp3d.com/products/aluminum-hub-6-jubilee-toolchanger-3d-printer Aluminum Hub, 6 mm ID] | ||
** [https://hightemp3d.com/products/rel-replacement-extension-spring-jubilee-toolchanger-3d-printer REL Replacement Extension Spring] | ** [https://hightemp3d.com/products/rel-replacement-extension-spring-jubilee-toolchanger-3d-printer REL Replacement Extension Spring] | ||
| + | * [https://powge.aliexpress.com/store/702327/search?SearchText=jubilee Powge] | ||
| + | ** [https://www.aliexpress.com/item/1005001516376637.html Jubilee Pulleys/Idlers/Belts Motion Kit] | ||
| + | ** [https://www.aliexpress.com/item/1005001516536336.html T8x2 Leadscrews, 375mm Long (leadscrew nuts are not threaded)] | ||
* [https://www.printedsolid.com/pages/search-results-page?q=jubilee Printed Solid] | * [https://www.printedsolid.com/pages/search-results-page?q=jubilee Printed Solid] | ||
| − | ** [https://www.printedsolid.com/products/ldo-jubilee-motor-kit Jubilee Motor Kit] | + | ** [https://www.printedsolid.com/products/ldo-jubilee-motor-kit Jubilee LDO Motor Kit] |
== Alternates == | == Alternates == | ||
Depending on region-specific constraints some parts may be harder to purchase. We welcome suggestions and will list them here. | Depending on region-specific constraints some parts may be harder to purchase. We welcome suggestions and will list them here. | ||
Revision as of 11:24, 11 October 2020
Purchased parts for Jubilee are broken down into multiple shopping lists
- (Current) Jubilee V2.1.2
- V2 Frame Shopping List (~$1350)
- V2 2x Direct Drive Extruder Shopping List (~$200 per tool)
- (Community Contributed) Jubilee V2.0.2 UK/EU BOM by HaythamB
- V2.0.2 Frame Shopping List last updated Apr 12, 2020
- (Deprecated) Jubilee V1
- V1 Frame Shopping List (~$1550)
- V1 2x Direct-Drive Extruder Shopping List (~$200 per tool)
Warnings About Cutting Your Own Extrusions
The shopping list specifies that the 2020 extrusions be cut-to-length by the vendor Misumi. This choice is intentional because Misumi can cut parts better (typically within +/- 0.1mm) than most Jubilee builders can without specialized tools. Later sections of the instructions also assume that extrusions of the same length are actually the same length; otherwise the squaring techniques in the instructions will not work. Long-story short: don’t cut the extrusions yourself unless you have a highly repeatable cutting setup.
Jubilee Component Vendors
Some small-scale manufacturers and part vendors are either reselling Jubilee’s hard-to-make parts, consolidating parts into kits, or selling modified parts from the stock model. These vendors are:
- 713Maker
- Mandala Rose Works
- SeeMeCNC
- Double Jump Electric (Joshua Vasquez)
- Filastruder
- Twist Locks
- T8x2 and T8x4 Leadscrews, 375mm long
- Tool Wedge Plates
- M3 and M4 Heat Set Inserts
- REL Extension Spring
- REL Hub
- Spring Guide
- Thrust Bearings
- Jubilee LDO Motor Kit
- Gates Pulley/Idler/Belt Motion Set
- Tool Balls
- Plum Couplers
- Shoulder Screws
- Jubilee Back Panel
- Coming Soon: Jubilee Fastener Kit
- Luke’s Laboratory
- High Temp 3D
- Powge
- Printed Solid
Alternates
Depending on region-specific constraints some parts may be harder to purchase. We welcome suggestions and will list them here.