3D Printed Parts
Revision as of 01:19, 29 May 2020 by Poofjunior (talk | contribs) (→Toolchanger Parts and Quantities)
Default Print Settings
Print all parts with the following print settings:
- PLA (Two PETG exceptions exist! See below)
- 0.4mm nozzle
- No supports
- 0.2mm layer height
- 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
- 20% infill * printable in the provided orientations
- outer perimeter layer first
- 2-3mm brim recommended, but not required
However, exceptions do exist! Please check the breakdown below for exceptions.
Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.
Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.
Frame Printed Parts and Quantities
- 1x PSU Socket Holder
- 1x Left Crossbar Pulley Reinforcement Plate
- 1x Right Crossbar Pulley Reinforcement Plate
- 1x Left Corner Pulley Reinforcement Plate
- 1x Right Corner Pulley Reinforcement Plate
- 2x Motor Reinforcement Plate
- 1x x_limit_trigger.STL
- 3x z_thrust_bearing_spacer.STL
- 1x back_z_motor_plate.STL
- 1x front_left_z_motor_plate.STL
- 1x front_right_z_motor_plate.STL
- 2x belt_clasp.STL
- 1x front_left_leadscrew_retainer.STL
- 1x front_right_leadscrew_retainer.STL
- 1x back_leadscrew_retainer.STL
- 1x back_right_foot.STL
- 2 perimeter layers is sufficient
- 1x back_left_foot.STL
- 2 perimeter layers is sufficient
- 1x front_right_foot.STL
- 2 perimeter layers is sufficient
- 1x front_left_foot.STL
- 2 perimeter layers is sufficient
- 1x front_left_bed_coupling_lift.STL
- 1x front_right_bed_coupling_lift.STL
- 1x back_bed_coupling_lift.STL
- 1x left_motor_plate.STL
- print from PETG
- Note: an aluminum version of this part is now available.
- 1x right_motor_plate.STL
- print from PETG
- Note: an aluminum version of this part is now available.
- 1x left_motor_corner_plate_spacer.STL
- 1x right_motor_corner_plate_spacer.STL
- 1x left_double_pulley_corner_bracket.STL
- print with support material
- 1x right_double_pulley_corner_bracket.STL
- print with support material
- 4x printed_pulley_spacer.STL
Toolchanger Parts and Quantities
- 1x spring_guide_capture.stl
- 1x twist_lock_spacer.STL
- 1x carriage_back_plate.STL
- 1x carriage_center_plate.STL
- 1x carriage_coupler_plate.STL
- 1x carriage_pulley.STL
- 1x fixed_half_pulley.STL
- 1x knob.STL
- 1x floating_half_pulley.STL
- print with support material
- 1x lock_actuator_base_plate.STL or stepperonline_lock_actuator_base_plate.STL
- 1x stepperonline_lock_actuator_motor_clip.STL or lock_actuator_motor_clip.STL
- 1x OPTTIONAL spring_guide_anchor_block.STL
Extruder-Specific Frame Parts
- 1x ooze_wiper.STL per tool
- 1x tool_cable_management_bracket.STL per tool
- 1x parking_post_base_47mm.STL per tool
- 1x tool_holder_47mm.STL per tool