3D Printed Parts

Default Print Settings

Print all parts with the following print settings:

• PLA
• 0.4mm nozzle
• No supports
• 0.2mm layer height
• 6 perimeter layers (This is especially critical for parts that have heat-set inserts)
• 20% infill * printable in the provided orientations
• outer perimeter layer first
• 2-3mm brim recommended, but not required

However, exceptions do exist! Please check the breakdown below for exceptions.

Note that parts that peel off the bed with a small curl cannot be used. They must stick to the bed such that they remain flat.

Other materials, such as PETG, may also work. We welcome feedback on various materials if others find them successful.

Frame Printed Parts and Quantities

• 1x PSU Socket Holder
• 1x Left Crossbar Pulley Reinforcement Plate
• 1x Right Crossbar Pulley Reinforcement Plate
• 1x Left Corner Pulley Reinforcement Plate
• 1x Right Corner Pulley Reinforcement Plate
• 2x Motor Reinforcement Plate
• 1x x_limit_trigger.STL
• 3x z_thrust_bearing_spacer.STL
• 1x back_z_motor_plate.STL
• 1x front_left_z_motor_plate.STL
• 1x front_right_z_motor_plate.STL
• 2x belt_clasp.STL
• 1x front_left_leadscrew_retainer.STL
• 1x front_right_leadscrew_retainer.STL
• 1x back_leadscrew_retainer.STL
• 1x back_right_foot.STL
  • 2 perimeter layers is sufficient
• 1x back_left_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_right_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_left_foot.STL
  • 2 perimeter layers is sufficient
• 1x front_left_bed_coupling_lift.STL
• 1x front_right_bed_coupling_lift.STL
• 1x back_bed_coupling_lift.STL
• 1x left_motor_corner_plate_spacer.STL
• 1x right_motor_corner_plate_spacer.STL
• 1x left_double_pulley_corner_bracket.STL
  • print with support material
• 1x right_double_pulley_corner_bracket.STL
  • print with support material
• 4x printed_pulley_spacer.STL

Toolchanger Parts and Quantities

• 1x spring_guide_capture.stl
• 1x twist_lock_spacer.STL
• 1x carriage_back_plate.STL
• 1x carriage_center_plate.STL
• 1x carriage_coupler_plate.STL
• 1x carriage_pulley.STL
• 1x fixed_half_pulley.STL
• 1x knob.STL
• 1x floating_half_pulley.STL
  • print with support material
• 1x lock_actuator_base_plate.STL or stepperonline_lock_actuator_base_plate.STL
• 1x lock_actuator_motor_clip.STL or stepperonline_lock_actuator_motor_clip.STL
• 1x OPTTIONAL spring_guide_anchor_block.STL

Extruder-Specific Frame Parts

• 1x ooze_wiper.STL per tool
• 1x tool_cable_management_bracket.STL per tool
• 1x parking_post_base_47mm.STL per tool
• 1x tool_holder_47mm.STL per tool

Assembly Fixtures Parts and Quantities

• 1x coupling_plate_pin_insertion_fixture.STL
• 1x z_lift_pin_insertion_fixture.STL
• 8x outer_frame_squaring_plate.STL

Deprecated Parts

These parts are no longer necessary in the latest version. They are:

• 1x left_motor_plate.STL
  • print from PETG
  • Note: an aluminum version of this part is now available.
• 1x right_motor_plate.STL
  • print from PETG
  • Note: an aluminum version of this part is now available.