Assembly Instructions

Let the build begin! Image Credit: @Danal on Discord

Building Jubilee can be broken down into the following high-level stages:

Building the frame with tool-changer mechanism
Connecting the electronics
Tuning the build for its target application
Building and connecting the tools

The instructions for the frame are detailed below.

For assembly instructions and wiring diagrams related to tools, see the page for that particular tool from the Tools page.

Questions about the assembly? Check out the FAQs, or reach out on Discord.

Hardware

For the mechanical assembly, all subassemblies are detailed with step-by-step visual instructions.

Pre-requisite Knowledge

Working with Heat-Set Inserts via the Plate Press Technique
Working with Inside Corner Brackets
How to use an Arbor Press
Tip: print this Fastener Reference Sheet at 100% scale for an easy sanity check.
How to crimp Molex Connectors

Frame Assembly Instructions

The instructions must be completed sequentially from Section 1 to Section 3. Instructions in the same section don’t depend on each other, so they can be done at the same time with a friend.

Part Prep

Before assembling the frame:

Heat Set Insert Installation
Inside Corner Bracket Prep

Section I

Outer Frame Assembly and Alignment
Aluminum Motor Plate Assembly
Double Pulley Corner Plate Assembly
Aluminum Crossbar Assembly
Toolchanger Remote Elastic Lock Assembly
Toolchanger Carriage Assembly
Magnetic Build Plate Assembly
Duet2 Electronics Panel Assembly
Coming Soon: Side Panel Assembly

Some instructions relate to older versions of the design. They are:

Section 2

Lower Frame Assembly
CoreXY Frame Assembly

Additionally, video Links to the CoreXY assembly are provided below:

Section 3

Z Axis Assembly

Electronics

Pre-Requisite Knowledge

Crimping Wires 🠔 only if you are scratch building and not sourcing premade harnesses.

Panel Layouts

Multiple electronics architectures are supported. Refer to the Duet Layouts PDF for screw mount locations for each setup.

Wiring Diagrams

All wires needed for the frame are called out in the corresponding wiring diagrams. Important Note: XY motors and ZZZ motors have different pinouts, which means their wires will have a different color coding. This color coding is respected in the diagram, but it is easy to mix up the included cables in real life. Do keep motors and the wires they came with together as a pair. Do not mix motor cables.

Duet 2 Wiring

Duet 2 Frame Wiring Diagram PDF
Duet 2 Example Back Panel Layouts

Duet3 Wiring

Duet3 Frame Wiring Diagrams

This wiring configuration matches the existing config files for the corresponding control board.

Duet 3 Example Back Panel Layouts

Duet 3 Mini + 3HC Expansion Wiring

Control Board Provisioning

Both the Duet2 + Duex5 Expansion board and the Duet3 Mini + 3HC configurations are fully supported.

To get a sense of the firmware requirements needed for porting Jubilee to other control boards, see the page on Adding Control Boards.

Duet 2 + Duex5

Duet 3 Mini + Duet 3HC

Duet 3 6HC + 3HC Expansion

TODO

Duet3 6HC + Pi + 3HC Expansion

Duet3 Raspberry Pi Provisioning
TODO

Duet3 Mini + Pi + 3HC Expansion

Duet3 Raspberry Pi Provisioning
TODO

Klipper

No "official path" exists for a Klipper Implementation of Jubilee, but there are 3 main options that you can adapt to your own motherboard and tool setup:

@ImpC's JubileeKlippper Repository
@Xon's JubileeKlippper Repository
@TypQxQ's Klipper_ToolChanger Repository

First Power-Up

Pre-Flight Checks

Tuning

Depending on your machine's target application, you may need to do some additional tuning.

Tuning Before Your First 3D Print

Tuning Before Multicolor Drawing

Tools